steve.roberts347
the list of supported decks show gemini mdj600
but when i plug them in my decks do not show on my laptop
my decks don't control the laptop like my old decks did
but when i plug them in my decks do not show on my laptop
my decks don't control the laptop like my old decks did
Mensajes Sun 08 Mar 20 @ 10:42 pm
locoDog
probably a driver
http://www.virtualdj.com/manuals/hardware/gemini/mdj600/setup.html
http://www.virtualdj.com/manuals/hardware/gemini/mdj600/setup.html
Mensajes Sun 08 Mar 20 @ 11:40 pm
steve.roberts347
thanks
will update decks later after work
will update decks later after work
Mensajes Mon 09 Mar 20 @ 6:57 am
steve.roberts347
decks have latest firmware
mdj600 is disabled in the vdj set up...how do i enable
my old cdj 650s work fine but we want to use the mdj 600
mdj600 is disabled in the vdj set up...how do i enable
my old cdj 650s work fine but we want to use the mdj 600
Mensajes Mon 09 Mar 20 @ 7:16 pm
locoDog
windows device manager does your operating system see the device without conflicts?
Mensajes Mon 09 Mar 20 @ 7:25 pm
steve.roberts347
when i plug the decks in it comes up with no sound card detected for mdj-600
also in controllers it says mdj-600 audio disabled
and is not listed in all controllers...
our other decks work fine it's just these
also in controllers it says mdj-600 audio disabled
and is not listed in all controllers...
our other decks work fine it's just these
Mensajes Mon 09 Mar 20 @ 7:51 pm
steve.roberts347
i don't understand what these settings are desired channel is set at 1 is that correct ?
To change the MIDI channel, make sure that you have the USB
source selected, then press SETTTINGS (9). Scroll down to the
entry called MIDI CHANNEL. Press the browse knob to select that
entry, then turn the browse knob to select the desired channel
(0-15 are available). Once you’ve selected the correct MIDI
channel, press the BACK button to exit Settings.
NOTE: In Settings, the MIDI channels are presented in
hexadecimal. If your software defines the MIDI channel in decimal,
just add 1 (so if Settings says channel “0” is selected, that is
channel “1”, and so on).
To change the MIDI channel, make sure that you have the USB
source selected, then press SETTTINGS (9). Scroll down to the
entry called MIDI CHANNEL. Press the browse knob to select that
entry, then turn the browse knob to select the desired channel
(0-15 are available). Once you’ve selected the correct MIDI
channel, press the BACK button to exit Settings.
NOTE: In Settings, the MIDI channels are presented in
hexadecimal. If your software defines the MIDI channel in decimal,
just add 1 (so if Settings says channel “0” is selected, that is
channel “1”, and so on).
Mensajes Mon 09 Mar 20 @ 7:56 pm
groovindj
Did you follow the setup guide (link in 2nd post)?
You need to install the ASIO drivers - assuming you're on PC (you haven't said).
You need to install the ASIO drivers - assuming you're on PC (you haven't said).
Mensajes Mon 09 Mar 20 @ 8:03 pm
steve.roberts347
yes all up to date
using a laptop
using a laptop
Mensajes Mon 09 Mar 20 @ 8:44 pm
locoDog
and you installed the drivers?
Mensajes Mon 09 Mar 20 @ 8:52 pm
steve.roberts347
will go and check again
thanks
thanks
Mensajes Mon 09 Mar 20 @ 9:03 pm
steve.roberts347
when we try to re install the drivers it just takes me to another page were there is no drivers to install..
anyone close to me in hyde cheshire willing to help i will pay for your time
anyone close to me in hyde cheshire willing to help i will pay for your time
Mensajes Mon 09 Mar 20 @ 10:05 pm
locoDog
have you even put it into midi mode?
Mensajes Mon 09 Mar 20 @ 10:23 pm
steve.roberts347
i never thought to do that...lol
yes i am not that stupid
as my other decks work fine so i must be done something right before
yes i am not that stupid
as my other decks work fine so i must be done something right before
Mensajes Mon 09 Mar 20 @ 10:39 pm