Hardware Manuals


Gemini - PMX10  

TOP PANEL CONTROLS





CONTROL

ACTION

1 CROSSFADER
Blends Audio signal from Left and Right channels
2 VOLUME
Adjust the Output Volume of Left/Right Channel. The series of leds next to each Volume fader indicate the pre-fader output level of Left/Right Channel
3 Master VU METER
This series of leds indicate the output level of Left/Right stereo channels of the Master Output
4 CUE
Use these buttons to send the pre-fader audio signal of Left/Right channel to the Headphones channel for pre-listening
5 FILTER
Apply a High/Low Pass Filter to Left/Right channel. When in middle position, no Filter is applied.
6 EQUALIZER
Adjust the 3 Equalizer bands (High/Mid and Low) for the Left/Right channel.
7 GAIN
Adjust the pre-fader output level of the Left/Right channel.
8 Master VOLUME
Adjust the output volume of the Master Output (connection at the rear panel)
9 BOOTH VOLUME
Adjust the output volume of the Booth Output (connection at the rear panel)
10 MIC LEVEL
Adjust the output volume of the Microphone Input (connection at the rear panel)
11 CUE/PGM
Blends audio signal from Master Output (when in PGM) and channels that have the CUE enabled (when in CUE) and sends to the Headphones Output (connection at the front panel)
12 CUE LEVEL
Adjust the volume of the Headphones Output (connection at the front panel)
13 TRACK SEARCH
Scrolls though files or folders depending on the selected Browser window.
When focus is on Folders list, push to set focus to the Files/Tracks List.

While the Sampler button is pressed, use this encoder to scroll through the available Sampler Banks.
While the Sampler button is pressed, push the encoder to scroll through the available Sampler Trigger modes (on/off, hold, stutter and unmute)

Push the encoder for more than 3 seconds to load the PMX10 Settings Pads page. See Advanced Setup for further details
14 LOAD
Press to load the selected track from Browser to the Left/Right deck.
Hold this button for more than 2 seconds, to switch the input of the Left/Right mixer channel to the analogue source (connections at the rear panel) or back to MIDI (for VirtualDJ Deck control)
15 BACK
Use this button to set focus to the Folders list of Browser. If focus is on the Folders List, use this button to open/close sub-folders
16 FX ON - BOTTOM
Use this button to toggle between FX Select and FX Param modes.
17 FX ON -TOP
Use this button to enable/disable the selected Effect on Left/Right Deck
18 EFFECT 1
Adjust the 1st Parameter of the selected Effect on Left/Right Deck
19 EFFECT 2
When the FX Select mode is enabled (default mode - FX ON BOTTOM is off) use this knob to adjust the 2nd Parameter of the selected Effect on Left/Right Deck.
When the FX Param mode is enabled (FX ON BOTTOM is on) use this knob to select the Effect for the Left/Right Deck
20 LOOP SIZE
Halve (anti-clockwise) /Double (clockwise) the size of the Loop
21 LOOP ON
Enable/disable an auto-loop of the selected size in beats
22 CUES
Sets the 8 colored Pads to Hotcues mode.
23 SAMPLES
Sets the 8 colored Pads to Sampler mode.
24 Pads
In Hotcues mode : Use the Pads to assign Hotcues 1 to 8 or jump to their stored positions if not assigned. Hold CUES button down and then press a Pad to delete its stored Hotcue.
In Sampler mode : Use the Pads to trigger samples 1 to 8 from the selected Sampler Bank. Depending on the selected Trigger mode, you may find useful to stop a playing sample, by holding down the SAMPLES button and pressing the related pad.


Frente y Atrás