S SHIFTPress this button down to access secondary actions as described in the SHIFT ACTION columnM MODEPress this button down to access third actions as described in the MODE ACTION column. If you release the button without pressing any other button to engage a shortcut, then the pad section of the unit will switch to the side you pressed the MODE button on.1 MONO/STEREOToggles the sound between STEREO and MONO. The sound will change on BOTH the headphones and the Master output.2 CROSSFADERBlends the audio between left and right channels3 VOLUMEAdjusts the channel volume4 CUE Sets , triggers and previews the temporary CUESlows down the track temporarily while playing (Pitch Bend). If not playing, it will move the current playback position (needle)Decreases the Key of the track by one Semitone5 PLAY Plays/Pauses the trackSpeeds up the track temporarily while playing (Pitch Bend). If not playing, it will move the current playback position (needle)Increases the Key of the track by one Semitone6 LOOPPress the button once to set a loop-in point (for manual looping). Press the button a second time to set a loop-out point and start the loop. While in loop, press this button to exit the loop.Toggles on/off an automatic loop. The length of the auto loop (in beats) is visible in the VirtualDJ GUI.Halves the size of the current loop (if the track is looping) or the size of the auto loop.7 SYNCSyncs the track's tempo and phase with opposite deckPress once to change the track's key by up to 2 semitones in order to become compatible with the other deck. Press a second time to reset the key back to it's original value.Doubles the size of the current loop (if the track is looping) or the size of the auto loop.8 PFLSends the deck's audio signal to the Headphones ChannelPress these buttons to select one of three available "mix effects" that can be used when crossfading between the tracks: Both LEDs off: No MixFx Left LED on : Filter Right LED on : Loop Roll Both LEDs on : Echo Out 9 FX PADDLEActivates the effect that's selected on the first effect slot on the VirtualDJ GUI.Activates a backspin effect10 FX DRY/WETControls the first effect parameter of the effect that's selected on the first effect slot on the VirtualDJ GUISHIFTED11 FX PARAMAdjusts the length (in beats) for beat-aware effects.Select the previous/next available effect for the first effect slot on the VirtualDJ GUI.12 FILTERControls the selected Color Effect for the channel. The default Color Effect is "Filter". You can choose different Color Effects from the VirtualDJ GUI.13 EQ LOWAdjusts the low (bass) frequencies, or the corresponding Stems according to the selected EQ Mode.14 EQ MIDAdjusts the middle (mid) frequencies, or the corresponding Stems according to the selected EQ Mode.15 EQ HIAdjusts the high (tremble) frequencies, or the corresponding Stems according to the selected EQ Mode.16 GAINAdjusts the pre-fader output level (Gain)17 Stems EQToggles the operation of the three EQ knobs between "Frequency" control and "Stems" control. When in "Frequency" mode, the button's led will be off, and the three knobs will control low, middle and high frequencies in a traditional 3 band equalizer manner. When in "Stems" mode, the button's led will be on, and the three knobs will control stem channels, depending on the selected EQ Mode. You can change the desired EQ Mode from VirtualDJ GUI.18 LOADLoads the selected track on browser to the deck. If the focus is on folders, switches the focus back on songs. Double click clones the tracks from the other deck.Switches left side between decks 1 & 3, and right side between decks 2 & 4.19 BROWSETurn: Scrolls through tracks and folders in VirtualDJ's browser. Push: Switches focus on folders, and opens/closes subfolders. If held down briefly, switches focus back to songs.Turn: Switches the selected sideview tab. Push: Switches focus between sideview and songs.Turn: Seeks through the track20 SPLITSplits the Pads to a dual view, so that Pads 1-4 are assigned to left deck, and Pads 5-8 are assigned to the right deck.21 Pads Performance RGB Pads . Operation depends on the selected Pads mode ( Pads page)Operation depends on the selected Pads mode ( Pads page)Selects one of the 8 available modes for Pads . The pre-defined modes are Hotcues, Loop Roll, Keycue, PADFX, Loop, Sampler , BeatJump and Stems . The pre-defined modes/pages can be changed to your needs. Please see How to assign Pad modes22 Master VOLAdjusts the volume of the Master Output channel. Hardware operation, but visible in VirtualDJ GUI23 PHONES VOLAdjusts the volume of the Headphones Output channel. Hardware operation, but visible in VirtualDJ GUI24 PHONES MIXBlends audio signal sent to headphones between Headphones channel (minimum position) and Master channel (maximum position). Hardware operation, but visible in VirtualDJ GUI
Hardware Integration Department
2024 - ATOMIX PRODUCTIONS
Reproduction of this manual in full or in part without written permission from Atomix Productions is prohibited.
