Sampler MODE

Press the top SESSION button, to set the device to Sampler mode (selected by default on start-up)

Pads

KEY

ACTION

SHIFT ACTION

1 to 64 Pads

Trigger * Sample 1 to 64 from the selected Sampler Bank. The led of each Pad will take the nearest available color of the Sample (as defined in Sampler Editor)

When Record Arm button (Bottom 1st) is enabled, the pad records a new sample and ads it to the same slot position in the Recording Bank

Stops the sample 1 to 64 of the selected Bank (useful when the Stutter or Un-mute trigger mode is selected)

* The Pads offer velocity. When enabled, the volume of the samples will be altered depending on how hard the pad is pressed. See further details at the Advanced Setup chapter

TOP BUTTONS

KEY

ACTION

SHIFT ACTION

T1 ARROW UP

Select previous available Sampler Bank

T2 ARROW DOWN

Select next available Sampler Bank

T3 ARROW LEFT

Halves the loop size of the selected/current Sampler (when it's set in Loop mode)

T4 ARROW RIGHT

Doubles the loop size of the selected/current Sampler (when it's set in Loop mode)

T5 SESSION

Selects the current Sampler mode

T6 NOTE

Selects the Effects mode mode

T7 DEVICE

Selects the Mixer mode mode

T8 USER

Selects the User's mode mode

LEFT BUTTONS

KEY

ACTION

SHIFT ACTION

L1 SHIFT

Press and hold down to access secondary actions, as described in the SHIFT ACTIONS column

L2 CLICK

Select the 'On/Off' Trigger Sampler mode.

L3 UNDO

Select the 'Hold' Trigger Sampler mode.

L4 DELETE

Select the 'Stutter' Trigger Sampler mode.

L5 QUANTIZE

Select the 'Un-Mute' Trigger Sampler mode.

L6 DUPLICATE

Not assigned

L7 DOUBLE

Not assigned.

L8 CIRCLE

Sets the selected/current sample to Loop mode

RIGHT BUTTONS

KEY

ACTION

SHIFT ACTION

R1 to R7 ARROW

Quick Bank select buttons. Select the 1st to the 7th first available Banks of Sampler . Banks (next/previous) can be selected from the Top Down/Up Arrow buttons

R8 ARROW

Select the Recordings Sampler Bank

BOTTOM BUTTONS

KEY

ACTION

SHIFT ACTION

B1 Record ARM

Enable Sampler Recording mode. When enabled, use Pads 1 to 64 to Record a new sample to the corresponding slot of the Recordings Bank

B2 TRACK SELECT

Select the Trigger Pads view (led is bright) where Samples are shown in boxes in GUI, or the Detailed view where samples are listed along with other properties and controls, such as Volume, Loop Size and Controls, etc.

B3 MUTE

Not assigned

B4 SOLO

Not assigned.

B5 VOLUME

Press to select the Sampler Volume Controls mode (led will become bright). In this mode, the Pads control the Volumes of the Samples, as explained further.
Press again to return to the default Trigger Sampler view.

B6 PAN

Press to select the Sampler Group Volume Controls mode (led will become bright). In this mode, the Pads control the Volumes of the Groups of the selected Bank (if available), as explained further.
Press again to return to the default Trigger Sampler view.

B7 SENDS

When enabled (default - led is bright), audio signal from Sampler will be routed to the Headphones channel as well..

B8 STOP CLIP

Stops all currently playing samples.

Sampler VOLUME MODE

When in Sampler mode, use the VOLUME button at the bottom [B5] to set Pads to Volume Control.



In this mode, the 8 columns of Pads adjust the Volume of the 1st to 8th sample of the selected Sampler Bank. Press a pad inside the column of the corresponding Sampler slot to gradually* adjust its Volume from the minimum (zero) - when lowest pad is pressed - to the maximum (volume 100%) - when the upper pad is pressed.

* The speed that the volume will increase/decrease to the set value, depends on the velocity (how hard the pad is initially pressed).

The Colors of the Pads in the same column will automatically get the color of the sample (1 to 8).

Note that if a sample (1 to 8) is assigned to a Sampler group, adjusting its volume will also adjust the volumes of all samples that are assigned to the same group. Sampler groups are defined in Sampler Editor.
If you wish to adjust the Volume of a single sample, without affecting the volumes of the other samples in the same group, use the right-side arrow buttons (R1 to R8) to select a block of samples (1 to 8, 9 to 16 ... etc up to 57 to 64). When all right-side arrow buttons are off, the Pads in the 8 columns will adjust the volume of all samples in the same group.

When in Sampler mode, use the PAN button at the bottom [B6] to set the 64 Pads to Volume Groups Control. In this mode, the 8 columns represent the volumes of the available Sampler groups in the selected Sampler bank. If no groups are defined/assigned to any sample, the Pads /columns will have no functionality.